Anasayfa Markalar Haberler Hakkımızda İK Sektörler Site haritası Üye Girişi
MAKİNE OTOMASYON ENDÜSTRİ
İletişim     |     Dokümanlar     |     English  
Sepetiniz boş
DİZEL MOTOR KONTROLÜ VE JENERATÖR EKIPMANLARI >> FW MURPHY Proses Takip Araçları >> Sıcaklık Sensör ve Göstergeleri
ANA MENÜ
FW MURPHY Proses Takip Araçları
Seviye Koruyucu
Seviye Göstergeleri
Basınç Sensörleri ve Göstergeleri
Hız/Zaman Sensörleri ve Göstergeleri
Sıcaklık Sensör ve Göstergeleri
- 76.TS Temperature Switch
- TSB Direct Mount Temperature Switch
- TC, RTD, RTDT series
- Thermocouples - 1/4
- Temperature Bulbs/Capillaries
- Thermowells
- TDXM
- TDX6
- MDTM89
    MDTM89



Murphy's model MDTM89 is an electronic, dual-temperature monitor. It monitors two thermocouples, displays the temperature of the thermocouple selected, and has adjustable trip points for each input. A toggle switch provides for selection of the thermocouple to be displayed and/or the temperature trip point to be checked/adjusted. If either trip point is reached, the associated output “turns on” and can be used as a control signal, or to initiate alarms and/or shutdown.

A “Push to Read” button, located below the selector switch, allows the operator to check the trip point and to see its value as adjustments are made. Two potentiometers, one on each side of the thermocouple selector switch, are provided for field-adjustment of the trip points.

There are four basic models. Two of the models are powered by capacitor discharge ignition, and have either an FET or an SCR output. One model operates from 12 or 24 VDC and has an FET output. One model operates from 120 VAC by use of an isolation module and has an FET output. Standard display is in degrees Fahrenheit; degrees Celsius is optional.


Applications

Applications include the following:
  • Compressor suction/discharge temperature
  • Engine/compressor jacket water temperature
  • Engine exhaust temperature
  • Compressor cylinder temperature
  • After cooler temperature
  • Bearing temperature

http://www.rekarma.com.tr/yonetim/urunresimb/703_1.jpg
Thermocouple Type

Either “J” or “K” type UNGROUNDED THERMOCOUPLE is accepted. Specify type in part number for each MDTM89 unit). You can also order thermocouples as a separate item.


Automatic Cold Junction Reference

Cold junction reference point compensation is an integral feature of the monitor. The compensator circuit monitors case temperature and automatically compensates for changes in ambient temperatures. Compensation will allow maximum of 2 degrees change in the temperature reading from 32 to 122°F (0 to 50°C).


Open Thermocouple Input

An open thermocouple input forces the monitor into upscale overrange. The monitor indicates an overrange by displaying the numeral 1 (one) in the left most digit of the display. An overrange will turn on the high trip point output.


Trip Point Operation

Monitored trip points are independent of the thermocouple selector switch. Both set points are always active. When the thermocouple temperature reaches the trip point temperature, the MDTM89 is triggered. After approximately 0.5 seconds the trip point output “turns on”. Trip points are set by depressing the “Push to Read” push button while rotating a trip point potentiometer until the desired trip point temperature is displayed.


Continuous and Trip Point Display

The selector switch is used to select the thermocouple or trip point temperature to be displayed. The selected temperature is continuously displayed during normal operation. Depressing the “Push to Read” push button displays the trip point temperature of the selected thermocouple.




Ürün Satışı / Teklif Talebi
Bu ürün için teklif iste
Broşürler
 MDTM89




webatolyesi